Schedule Service

 

What're your ideas regarding How to Install a Bathtub Yourself?

Installing a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a new one is also a reasonably challenging task. If the old tub is conveniently obtainable, the task can move immediately; if you need to open up a wall surface to remove the old tub and also place the new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the brand-new one. See to it you have actually certified on your own for the task as well as fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will help you mount a new bathtub in your washroom if you have currently gotten a new bathtub as well as don't need to change the arrangement of your previous water pipes.
Your devices and also product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

First of all, the supporting framework provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final placement.

 

 

Removing Old Touches

If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be quite problematic due to the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Setting up the Tub

Using the two wooden boards under its feet, place the tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water system and inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill the tub as well as additionally examine the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bathtub has actually been made use of a minimum of when as this will certainly settle it into its final setting.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in location between the tap and also the sink. Secure the tap in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, creating the water to pass through the wall between the bath and also the tiling, bring about issues with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave feedback further down. We'd be glad to hear your reactions about this piece. In hopes that you visit us again in the future. So long as you enjoyed reading our blog entry plz do not forget to pass it around. Thanks a lot for going through it.

Ready to assist!